Separating individual die in a wafer using chemical methods.

Taking place at the end of the semiconductor process flow, dicing is the process where the silicon wafer is finally turned into individual chips, or die, traditionally by means of a saw or laser. A saw blade, or laser, is used to cut the wafer along the areas between the chips called dicing lanes. This step separates the chips from the wafer making them ready to be packaged and fitted to whichever device they will end up in.

Plasma dicing achieves the same outcome with a dry etching process that uses a fluorine plasma to etch away the material in the dicing lanes between the chips. Plasma dicing is gaining acceptance within the semiconductor industry as the preferred solution, versus blades or lasers, particularly as chips get smaller, thinner, and more complex.

Blade dicing is the process of using an abrasive disc (blade) rotating at high speed to cut along the dicing lanes. Typically, the blade tip is made of abrasive grit or extremely thin diamond, and can be used to dice through, i.e., cut, or simply groove the silicon wafer. However, just like any mechanical cutting method, blade dicing relies on physical removal of material that can cause chipping and cracking of the die, resulting in damaged product and lower yields.

Laser dicing, as the name suggests, uses laser technology to separate the wafer into die. The process involves delivering high concentrations of photon streams onto the wafer, generating a spot of high localized temperature to remove the dicing lane area, between the chips. The laser heats the material to such a temperature that the area under the laser spot is blown away (ablated) or simply vaporized. The laser can also be focused to deliver this heat into the bulk of the wafer, this method is called “stealth” laser dicing. For this approach, the heat from the laser creates voids within the dicing lane. These weakened regions then act like a perforation and tear apart when the wafer is expanded. In comparison to the blade saw method, laser dicing is considerably more costly.

Plasma dicing offers many benefits in comparison to other traditional dicing methods.

Plasma dicing removes the material in the dicing lane chemically. There is no mechanical damage, no heat affected zones or other physical impact on the die. This means that plasma dicing causes no damage. Die, singulated by plasma, have higher break strength compared to those singulated by blade or laser.

This gain in mechanical integrity is a particular advantage for die subject to physical stresses in service, such as those used in hybrid bonding stacks for high bandwidth memory (HBM), where if one chip in the stack fails, the whole device is lost.

With a move toward much thinner die, the non-mechanical nature of plasma dicing is a valuable attribute as industry roadmaps push thicknesses below 50µm.

Blade dicing and laser dicing are “serial” processes cutting along the dicing lanes one after the another. For laser, specifically, multiple passes may be needed. Plasma dicing removes all the dicing lanes “in parallel” at the same time. This means as die sizes shrink (i.e., more dicing lanes and therefore more cuts required), and wafers get thinner (less silicon for plasma to remove, or lower blade speeds/laser powers needed to avoid damage), there are cross-over points where plasma dicing becomes the fastest process.

Without any physical restrictions such as blade width or laser spot size to accommodate, plasma can enable a move to narrower dicing lanes, providing an opportunity to increase the die output of a production line. Freeing up wafer real-estate, previously sacrificed for the mechanical singulation method, can now be allocated to additional active die. The potential for die count gains is significant, particularly when smaller die sizes are considered.

As the wafer layout is not constrained by the need to have linear dicing paths, plasma dicing can offer device designers much greater flexibility with regard to fundamental die shape/size, removing guard rings, and positioning of die/test groups to make better use of the wafer area.

Test structure illustrating flexibility of design for plasma dicing.

Plasma dicing is also attractive for fragile devices such as micro-electro-mechanical systems (MEMS). For example, inertial sensors which consist of tiny movable structures would stand to benefit from a clean, non-mechanical singulation method. There would be no physical forces to vibrate the wafer and cause damage to the sensing features, or particles to jam in between them and affect their movement.

The chemical nature of plasma dicing produces only gaseous by-products, which are removed by vacuum pumping leaving a clean wafer surface, critical in applications such as hybrid bonding. Mechanical dicing or laser ablation can result in debris or particulate contamination across the wafer surface (which can be detected using the ICOS F160XP die sorting and inspection system) even with careful cleaning/drying.

So, while conventional dicing methods will continue to be a cost-effective solution for many applications, there are a growing number of cases where plasma dicing can offer greater yields, flexibility, and throughput, resulting in a lower cost of ownership overall. Learn more about the benefits of plasma dicing by watching our recent SPTS Webinar.

If you would like to discuss your own dicing requirements and find out if SPTS plasma dicing can solve any issues with your current solution, get in touch with us.

[This blog was first published in KLA Advance.]

Name* (Note: This name will be displayed publicly)

Email* (This will not be displayed publicly)

Who’s doing what in next-gen chips, and when they expect to do it.

Manufacturability reaches sufficient level to compete with flip-chip BGA and 2.5D.

Steps are being taken to minimize problems, but they will take years to implement.

But that doesn’t mean it’s going to be mainstream anytime soon.

L5 vehicles need at least 10 more years of development.

Increased transistor density and utilization are creating memory performance issues.

Suppliers are investing new 300mm capacity, but it’s probably not enough. And despite burgeoning 200mm demand, only Okmetic and new players in China are adding capacity.

The industry reached an inflection point where analog is getting a fresh look, but digital will not cede ground readily.

Who’s doing what in next-gen chips, and when they expect to do it.

100% inspection, more data, and traceability will reduce assembly defects plaguing automotive customer returns.

Engineers are finding ways to effectively thermally dissipate heat from complex modules.

Manufacturability reaches sufficient level to compete with flip-chip BGA and 2.5D.

Steps are being taken to minimize problems, but they will take years to implement.